A Beginner's Guide to Plumbing for Bathtub Installation
A Beginner's Guide to Plumbing for Bathtub Installation
Blog Article
The author is making a number of good points about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround as a whole in this content directly below.
Installing a bath tub isn't specifically rocket science, yet it does need solid plumbing, woodworking, as well as often, tiling skills. Changing an old bathtub with a brand-new one is likewise a moderately challenging project. If the old tub is easily easily accessible, the project can move rapidly; if you have to open a wall surface to eliminate the old tub and place the new bathtub, the job is much harder. In either instance, the project is within a residence handyman's skills, although you will certainly need a helper to vacate the old tub and also set in the new one. Make sure you have certified on your own for the task and also fit attempting it. As opposed to working with a specialist to take control of a halfway-completed job, it is much better to think about using one before you start. Opportunities are you may need an expert plumber to make tube connections.
This article will help you mount a new tub in your washroom if you have actually currently acquired a brand-new tub and don't require to change the arrangement of your previous supply of water pipes.
Your devices as well as material checklist should comprise the following:
Getting ready for the Setup
To start with, the sustaining frame provided with the bath needs to be fitted (if needed) according to the supplier's instructions. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is essential to make certain that if the tap comes with a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bath, it is also reasonable to fit a supporting plate under the taps unit to stop strain on the tub.
Fit the versatile tap connectors to the bottom of both taps making use of 2 nuts and also olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom must now prepare to be fitted in its final position.
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is disconnect the water system. After doing so, activate the faucets to drain any kind of water staying in the system. The procedure of eliminating the existing faucets can be quite bothersome due to the restricted gain access to that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a cloth all set for the continuing to be water that will come from the pipes. When the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from turning throughout this procedure. Once the taps have been removed, the holes in the bath/basin will have to be cleansed of any old securing substance.
Before proceeding to fit the new faucets, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new taps to fit.
Installing the Bathtub
Utilizing the two wooden boards under its feet, put the bathtub in the required position. The wood boards are useful in evenly spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four little points.
The next objective is to guarantee that the bathtub is leveled all round. This can be achieved by examining the spirit level and readjusting the feet on the bathtub up until the spirit level reviews level.
To install taps, fit the bottom of the furthest adaptable faucet connector to the ideal supply pipe by making a compression sign up with; then do the same for the other tap.
Activate the supply of water as well as examine all joints and also brand-new pipework for leakages as well as tighten them if essential. Fill up the bathtub and additionally inspect the overflow outlet as well as the typical electrical outlet for leakages.
Finally, deal with the bathroom paneling as described in the producer's user's manual. Tiling and sealing around the bath tub needs to wait up until the tub has actually been utilized at least once as this will resolve it right into its last setting.
Fitting New Touches
If the tails of the new faucets are plastic, then you will require a plastic connector to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap and also the various other end offers a connection to the existing supply pipes.
If you require to fit a monobloc, then you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the placing opening in the bath/basin making sure that the washers remain in location between the faucet as well as the sink. Secure the faucet in place with the producer provided backnut. When the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal tap adapters. The previous type must be linked to the tap ends initially, tightening up only by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bathroom satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is very important as the installation can move enough to break a rigid seal, causing the water to penetrate the wall in between the bathroom as well as the tiling, resulting in problems with dampness and also possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components as well as fittings. They are offered in tubes as well as cartridges, and also can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of soaked newspaper or soft rope. Remember to constantly load the tub with water before securing, to enable the activity experienced when the tub is in usage. The sealer can break relatively very early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally quickly offered on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or water resistant adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed reading our article on How to Install a Bathtub Yourself. Thank you so much for taking a few minutes to read our piece of content. Enjoyed our review? Please share it. Help another person find it. Thank you so much for taking the time to read it.
Book My Estimate Report this page